This page is on a secure connection, protected by Comodo® SSL

Schneider MDrive Plus NEMA23

Schneider MDrive Plus NEMA23
2 In Stock
Schneider Electric
Was: £308.39 Now: £226.70 (£272.04 inc tax)
Secure ordering via SagePay & PayPal
Fast delivery from UK stock

Schneider MDrive Plus - Motion Control

MDI•23 | NEMA23 Integrated motor and controls

MODEL available in stock: MDI1PRL23B7

The MDrive Plus NEMA23 Motion Control offers system designs a low cost, intelligent motion controller integrated with a NEMA 23 high torque stepper motor and a +12 to +75 volt microstepping drive.

MDrive® Plus Motion Control products integrate 1.8° 2-phase stepper motor, fully programmable motion controller, drive electronics and optional encoder. Products with encoders include stall detection, position maintenance, and find index mark.

 Programming for these stand-alone motion control solutions is via RS-422/485 interface with MCode software using simple 1 to 2 character instructions. ModbusTCP protocol is also available.

General Features

  • +12 to +75 VDC single supply
  • 20 microstep resolutions up to 51,200 steps per rev including: Degrees, Metric, Arc Minutes
  • Holding torque: 64-200 N-cm
  • Auxiliary logic power supply input
  • 0 to 5 MHz step clock rate selectable in 0.59 Hz increments
  • Up to 8 I/O lines
  • One 10 bit selectable analogue input
  • Communications: RS-422/485
  • Protection: IP20, IP65 ratings
  • Programmable : Motor run / hold current
  • Available options: Motor stack lengths
  • Connector options
  • Optional encoders
  • Rear control knob for manual positioning 

Application areas

MDrive Plus products deliver reliable performance for new and existing motion control applications. Satisfying the requirements for a wide range of machine builders. Simplify your machine design and reduce cabinet size by replacing multiple components with a single compact integrated motor. Fewer individual ystem components eliminate multiple potential failure points, and lowers risk of electrical noise by eliminating cabling between motor and drive.

These compact, powerful and cost effective motion control solutions deliver exceptional smoothness and performance that can reduce system cost, design and assembly time for a large range of 2-phase stepper motor applications.

download button


PLEASE NOTE: The model MDI1PRL23B7 selling on the e-shop here is re-conditioned so there will be NO warranty covered.

For any new applications or any other standard warranty-covered MDrive products, please contact our technical sales team at (+44) 01202 599922 or by email for the further details & quotes.

Planetary Gearbox with NEMA 23 Mounting Flange

Planetary Gearbox with NEMA 23 Mounting Flange

The RE55 Nema 23 gearbox is a high quality planetary gearbox. It comes with a NEMA 23 input flange for direct mounting to a standard NEMA 23 frame stepper motor. Three gear ratio options are available in stock: 42:1.

£136.50 (£163.80 inc tax) Out of stock
Email me when back in stock!
0 In Stock
Din Rail Regulated Power Supply-DPS (24vdc outputs)

Din Rail Regulated Power Supply-DPS (24vdc outputs)

Our new DPS series regulated, single output industrial DIN Rail power supply featured with short circuit, overload and over voltage protection. It can be installed on DIN Rail TS-35/7.5 or 15 and offers cooling by free air convection.

£30.98 (£37.18 inc tax)
28 In Stock
Regulated Switch-mode Power Supplies

Regulated Switch-mode Power Supplies

RSP-320 and SPS series switching mode power supplies with universal AC input /full range of 85-264VAC to provide 24V/ 36V/ 48V/ 60VDC output voltage for the output current 0-12.5A.

15 In Stock
4 In Stock
5 In Stock
4 In Stock